Veritas PM-V11 Blade for Low-Angle Smooth Plane, 2", 25° Bevel
kr682.50
Tax included
Replacement 2" blade in PM-V11 steel with a 25° bevel, for the Veritas low-angle smooth plane. Among woodworkers, hand plane users are arguably the most demanding of their tools.
Replacement 2" blade in PM-V11 steel with a 25° bevel, for the Veritas low-angle smooth plane.
Among woodworkers, hand plane users are arguably the most demanding of their tools. After all, one of the uses of hand planes is to produce surfaces that are ready for finish and reflect the level of craftsmanship that has gone into the project.
To achieve finish-quality surfaces, a sharp edge on your plane blade is critical; however, maintaining a sharp edge can be time consuming, even with the appropriate sharpening equipment. All woodworkers have wrestled with the question of when to stop planing with a blade and invest the time in sharpening it before continuing.
The PM-V11 alloy was developed to give woodworkers what they asked for: a blade that holds a fine, durable edge without requiring costly new sharpening equipment. Veritas PM-V11 plane blades strike a fine balance between performance, ease of sharpening and cost.
Like all Veritas O1 and A2 blades, PM-V11 blades are fully lapped and ready for final honing.
05P25.72
Specific References
- EAN13
- 722356012420
- MPN
- 05P2572
- HS code
- 8208200000
Veritas bevel-up planes hold the blade bevel up in a 12° bed. The cutting angle is therefore the bed angle plus the blade's bevel angle:
A 25° blade gives a 37° cutting angle – good for end grain and easy wood
A 38° blade gives a 50° cutting angle (York pitch) – a good start for difficult grain
A 50° blade gives a 62° cutting angle – for the most difficult wood
You change the cutting angle by swapping blades, or by honing a higher micro-bevel on the blade you have.
Which blade fits depends on the width of the plane. The blades come in A2, O1 and PM-V11 and with a 25°, 38° or 50° bevel:
1-5/8" – the Low-Angle Block Plane
1-3/4" – the Small Bevel-Up Smoother
2" – the Low-Angle Smooth Plane
2-1/4" – the Low-Angle Jack Plane, the 164 smoother and the Bevel-Up Jointer
Toothed A2 blades are also available for several of the planes, for difficult grain and for keying surfaces before veneering.
Veritas planes come with three types of steel. All give sharp edges, but they differ in how long the edge lasts and how easy the steel is to sharpen:
O1 – carbon steel that gets very sharp and is the easiest to hone
A2 – tool steel that holds an edge longer but takes a little longer to sharpen
PM-V11 – Veritas powder-metallurgy steel that holds an edge long and is still easy to sharpen
PM-V11 is the premium choice. O1 suits you if you sharpen often and want the keenest edge.
There are several good ways to sharpen chisels and plane irons: water stones, diamond stones, oil stones and sharpening machines such as Tormek. All give sharp edges, but they differ in speed, maintenance and price.
A honing guide makes it easier to keep the same angle every time. The most important thing is to find a method you enjoy and use often. The guide helps you choose.
Planes of cast iron and steel rust easily, especially in unheated workshops and from moisture on your hands. Wipe the plane after use and protect bare surfaces with a thin layer of wax or oil that will not mark the wood.
Store your planes dry, ideally in a plane sock or box. If rust has already formed, the guide shows how to clean and protect them.
A new replacement iron can make an old plane better than it was when new. To find the right one, measure the iron's width, thickness and slot dimensions, and check whether the plane has a cap iron and what kind of adjuster it has.
A thicker iron chatters less but may require the mouth to be adjusted. The guide shows how to measure and choose correctly. You can also send us a photo of the iron with a rule beside it, and we will help you. We do not sell adjusting screws or other spare parts for old Stanley planes.
Most products are restocked on an ongoing basis, but delivery times from the manufacturer vary. When an item is out of stock, the button Notify me when available appears on the product page.
Click the button and enter your email address, and we will email you as soon as the item is back in stock. If you are logged in, your email address is registered automatically. If you want to know when the next delivery is expected, you are welcome to contact us.
How often items are restocked depends on the supplier. We receive deliveries from Veritas about once a month, Lie-Nielsen ships in batches and we order from Incra about once a year. You can also add the item to a wishlist in your account, where you can see whether it is in stock.
Comments (0)
No customer reviews for the moment.
Customers who bought this product also bought:
16 other products in the same category:
Viewed products
Replacement 2" blade in PM-V11 steel with a 25° bevel, for the Veritas low-angle smooth plane. Among woodworkers, hand plane users are arguably the most demanding of their tools.