Question 1

Will this product be back in stock?

Accepted Answer

Most products are restocked on an ongoing basis, but delivery times from the manufacturer vary. When an item is out of stock, the button Notify me when available appears on the product page.

Click the button and enter your email address, and we will email you as soon as the item is back in stock. If you are logged in, your email address is registered automatically. If you want to know when the next delivery is expected, you are welcome to contact us.

How often items are restocked depends on the supplier. We receive deliveries from Veritas about once a month, Lie-Nielsen ships in batches and we order from Incra about once a year. You can also add the item to a wishlist in your account, where you can see whether it is in stock.

Question 2

Do you only sell products that are in stock?

Accepted Answer

Yes, as a rule we only sell products we have in stock, unless stated otherwise on the product page. The stock status is shown on every product page.

If a product is still temporarily out of stock, we try to ship the complete order within a reasonable time. If that is not possible, we ship what we have, and the back-ordered item is sent separately once it has arrived.

Question 3

Do the product photos match the item exactly?

Accepted Answer

We try to show product photos that are as accurate as possible, but the images should be seen as illustrations. Details such as colour, type of wood, finish and packaging may differ slightly from the item you receive, for example when the manufacturer changes the design.

If you are unsure about a detail, such as exact dimensions or what is included, you are welcome to contact us before you order. If the photo and the text show different dimensions, the text applies.

Question 4

Do you sell gift cards?

Accepted Answer

Yes, we sell gift cards in different amounts. A gift card is an easy way to give tools, books or materials to someone who enjoys wood and craft, and the recipient chooses what they want.

You buy gift cards under My account, Gift cards. Enter the gift card code in the Gift card field in the cart, not in the Voucher field.

Gift cards bought from summer 2026 onwards are valid for 1 year. Older gift cards have no time limit.

Question 5

How do I change the cutting angle on a Veritas bevel-up plane?

Accepted Answer

Veritas bevel-up planes hold the blade bevel up in a 12° bed. The cutting angle is therefore the bed angle plus the blade's bevel angle:

A 25° blade gives a 37° cutting angle – good for end grain and easy wood
A 38° blade gives a 50° cutting angle (York pitch) – a good start for difficult grain
A 50° blade gives a 62° cutting angle – for the most difficult wood

You change the cutting angle by swapping blades, or by honing a higher micro-bevel on the blade you have.

Question 6

Which blade fits my Veritas bevel-up plane?

Accepted Answer

Which blade fits depends on the width of the plane. The blades come in A2, O1 and PM-V11 and with a 25°, 38° or 50° bevel:

1-5/8" – the Low-Angle Block Plane
1-3/4" – the Small Bevel-Up Smoother
2" – the Low-Angle Smooth Plane
2-1/4" – the Low-Angle Jack Plane, the 164 smoother and the Bevel-Up Jointer

Toothed A2 blades are also available for several of the planes, for difficult grain and for keying surfaces before veneering.

Question 7

A2, O1 or PM-V11 – which steel should I choose for my Veritas plane?

Accepted Answer

Veritas planes come with three types of steel. All give sharp edges, but they differ in how long the edge lasts and how easy the steel is to sharpen:

O1 – carbon steel that gets very sharp and is the easiest to hone
A2 – tool steel that holds an edge longer but takes a little longer to sharpen
PM-V11 – Veritas powder-metallurgy steel that holds an edge long and is still easy to sharpen

PM-V11 is the premium choice. O1 suits you if you sharpen often and want the keenest edge.

Question 8

Is a blade included when I buy a Veritas plane?

Accepted Answer

Most Veritas planes are supplied with a lapped blade, and the product name states which steel is included, for example A2, O1 or PM-V11.

Some versions are sold without a blade or as the body only, so you can choose the steel and bevel angle yourself. The name then says "without blade" or "body only". You will find matching blades among the Veritas replacement blades.

Question 9

Will the Hock blade fit my Stanley or Record plane?

Accepted Answer

Yes, Hock plane irons fit 99.9% of Stanley and Record style planes with no changes other than a simple frog adjustment. The blades are 3/32" thick and 7" long.

Choose the blade by the number of your plane:
No. 3
No. 4 and 5
No. 4 1/2, 5 1/2, 6 and 7
No. 8
Older No. 5 1/2 planes have their own blade

Because the Hock blade is thicker than the original, the mouth may need adjusting with the frog.

Question 10

Should I choose a Hock blade in O1 or A2?

Accepted Answer

Hock makes its plane irons in two types of steel:

O1 – high-carbon steel that is easier to hone and gets sharper
A2 – cryogenically treated tool steel that holds an edge longer

Both are a big improvement on the thin blades supplied with many new planes. A2 is recommended for hard and abrasive materials, such as bamboo. If you sharpen often and want the keenest edge, O1 is a good choice.

Question 11

Do I need a new cap iron for my Hock blade?

Accepted Answer

You do not have to, but it often gives a noticeable improvement. Hock cap irons are 3 mm thick, almost twice as thick as a standard chip breaker. The extra thickness stabilises the blade's cutting edge and reduces vibration and chatter. A knurled cap screw is included. Choose the cap iron for the same plane number as the blade, and they will match.

Question 12

Which Hock blade fits my block plane?

Accepted Answer

Hock block plane blades are 3/32" thick and 4 1/4" long and fit Stanley and Record block planes. You choose by width and slot: Width: 1 3/8" for Stanley low-angle block planes and 1 5/8" for the No. 9 1/2 and similar Slot: 7/16" for older planes and 5/8" for newer Stanley planes Measure the slot in your old blade before you order. The blades come in both O1 and A2.

Question 13

Which Pégas scroll saw blade should I choose?

Accepted Answer

Pégas makes many types of scroll saw blade, and the choice depends mainly on the material: Skip – a universal blade, very efficient in hard and medium-hard wood Double Skip – a fast blade with good chip removal that does not burn, good for soft wood Super Skip – aggressive but with a smooth finish, for hardwood and acrylic Super Hook – for thick hardwood, cuts up to 76 mm of beech Spiral – cuts in every direction without turning the work Metal cutting – for thin metal up to 3 mm Blades marked R (Reverse) give a cleaner underside.

Question 14

What does R (Reverse) mean on Pégas scroll saw blades?

Accepted Answer

An R after the number, for example 7R, means the scroll saw blade is a Reverse blade. It has the same tooth geometry as the matching standard blade, but with a few reverse teeth at the bottom. The reverse teeth cut upwards and prevent the wood from splintering on the underside of the work. This gives a cleaner edge on both faces and works especially well in soft wood and plywood. Set the blade so the reverse teeth just reach above the table.

Question 15

Which number of Pégas scroll saw blade should I choose?

Accepted Answer

The number indicates the blade size. The higher the number, the thicker and wider the blade, with fewer teeth per inch. A Skip blade No. 2/0, for example, has 28 teeth per inch, No. 5 has 17 and No. 12 has 11.5. Low numbers (2/0–3) suit thin material, veneer and tight curves. Middle numbers (4–7) are good all-round blades for 10–20 mm wood. High numbers (8–12) cut faster in thick and hard wood but cannot follow such tight curves.

Question 16

Should I choose pinned or plain-end scroll saw blades?

Accepted Answer

It depends on your saw. Pinned scroll saw blades have cross pins at the ends and are used in saws that require them, such as coping saws and some hobby saws. The 3" blades with a 70 mm pin centre fit, among others, Dremel, Sears, Delta and Emco Lux. Plain-end blades are used in most power scroll saws and in hand-held saw frames, and they can be threaded through a drilled hole for inside cuts.

Question 17

Which jaws do I need for the Lie-Nielsen honing guide?

Accepted Answer

The Lie-Nielsen honing guide is supplied with the standard jaws, which fit most Lie-Nielsen plane blades and bevel-edge chisels 1/4"–3/4". For other tools there are extra jaws: Chisel jaws – for 1/8" and 3/16" chisels Mortise chisel jaws – for all Lie-Nielsen mortise chisels and the 1" chisel Long jaws – for short blades, such as spokeshaves and the No. 10 1/4, 041, 042, 073 and 85 planes Skewed jaws 18° and 30° – for skewed blades, such as the No. 140 block plane The jaws are made for Lie-Nielsen's own blades and chisels and do not always fit other makers' tools.

Question 18

Should I choose a Lie-Nielsen plane in bronze or cast iron?

Accepted Answer

The planes work the same way and have the same blade, frog and precision, so the difference is the material of the body: Bronze – heavier, which gives a calm, steady stroke, and it does not rust. The surface develops an attractive patina over time. Cast iron – a little lighter and less expensive. The surface needs protecting against rust with wax, for example. A No. 4 smoothing plane in bronze weighs 2 kg, for example, while the same plane in cast iron weighs 1.8 kg. Choose bronze if you want extra mass and no rust, and cast iron if you want a lighter plane at a lower price.

Question 19

Can I fit a higher-angle frog to my Lie-Nielsen bench plane?

Accepted Answer

Yes. Lie-Nielsen bench planes come with a frog bedded at 45° as standard, just like Stanley planes. For the No. 4 and No. 5 planes there is a frog with a 50° bed angle (York pitch). The higher angle makes it easier to smooth wood with difficult grain without tear-out. The frog is swapped in a few minutes and fits Lie-Nielsen planes that take a 2" (51 mm) blade. For the No. 4 1/2, 5 1/2, 6 and 7 there are frogs for 2 3/8" (60 mm) blades. The frogs do not fit other makes.

Question 20

What steel are Lie-Nielsen plane blades and chisels made of?

Accepted Answer

Most Lie-Nielsen plane blades, chisels and mortise chisels are made of A2 tool steel. The steel is cryogenically treated, hardened to 60–62 HRC and double tempered, and takes and holds a very fine edge for a long time. The blades are surface ground on the top, back and edge, so they quickly take a mirror finish. Some tools are available in O1 carbon steel, which gets very sharp and is easy to sharpen. The product name then says O1.

Question 21

Should I soak my Naniwa stone?

Accepted Answer

It depends on which series the stone belongs to: Super Stone / Superstone (S1, S2) – do not soak. Splash water on the surface and sharpen (splash and go). Prolonged soaking can damage the stone. Professional – does not need soaking. Wet the surface and keep it wet while sharpening. Traditional and Aotoishi – soak the water stone for 10–15 minutes, until the bubbles stop. Always let the stone dry at room temperature after use, not in the sun or on a radiator.

Question 22

Which grit of Naniwa stone should I choose?

Accepted Answer

The grit indicates how coarse or fine the sharpening stone is. The lower the number, the coarser the stone: 220 – for repairing damaged or very dull edges and changing the bevel angle 1000 – basic sharpening, the most important stone if you only have one 1500–3000 – an intermediate step that gives a keener edge 5000–8000 – fine honing to a very sharp edge 10000–12000 – polishing to a mirror finish A good start is a 1000 stone and a fine stone of 5000–8000. The 220/1000 and 1000/3000 combination stones give two grits in one stone.

Question 23

What is the difference between Naniwa S1 and S2?

Accepted Answer

The Naniwa Superstone comes in two thicknesses with the same abrasive and grits: S1 – 10 mm thick, lighter and less expensive S2 – 20 mm thick, lasts about twice as long Both measure 210 × 70 mm and sharpen in the same way, so the choice is about how long the stone should last. If you sharpen often, the thicker S2 pays off. Neither should be soaked. To keep the stone steady you can use the Naniwa stone holder, which fits stones 136–218 mm long.

Question 24

What is the Naniwa nagura stone used for?

Accepted Answer

A nagura stone is a small stone that you rub on the surface of a wet fine stone before you start sharpening. It raises a fine slurry that helps the stone polish the edge, especially on very fine stones that can otherwise feel slick. The Naniwa nagura stone is most useful on the Professional series and on finer Naniwa stones of 5000 grit and up. It also cleans the surface and makes the stone cut more evenly. The nagura stone measures 70 × 51 × 35 mm.

Question 25

What is the difference between the Tormek T-4 and T-8?

Accepted Answer

Both machines sharpen all common edge tools with the same jig system. The difference is in size and capacity: Tormek T-4 – 200 mm grindstone, 120 W motor for intermittent use (30 min per hour), weighs 8 kg. For home and hobby use. Tormek T-8 – 250 mm grindstone, solid cast housing with minimal play and an industrial motor for continuous use, weighs 14.8 kg. For those who sharpen a lot. The T-8 Custom is a T-8 without stone and honing wheel, so you choose your own. The T-4 Bushcraft is a T-4 with a knife jig and axe jig in the box.

Question 26

Which grindstone should I choose for my Tormek?

Accepted Answer

First choose the right grindstone size: 200 mm for the T-4 and 250 mm for the T-8. Then choose by what you sharpen: Original grindstone SG – an all-round stone supplied with the machine. With the SP-650 stone grader you change the surface from 220 grit to about 1000 grit. Blackstone Silicon SB – for high-speed steel (HSS), such as turning tools Japanese water stone SJ – 4000 grit for a polished, razor-sharp edge Diamond wheel DC, DF or DE – 360, 600 or 1200 grit, for any material including ceramics and carbide. Use the ACC-150 anti-corrosion concentrate in the water.

Question 27

Which jigs do I need for my Tormek?

Accepted Answer

The jigs are usually not included with the machine; you choose them by the tools you want to sharpen. All jigs fit both the T-4 and the T-8: SE-77 – chisels and plane blades with a straight or slightly cambered edge KJ-45 and KJ-140 – centring knife jigs for symmetrical bevels SVD-186R – turning gouges, carving gouges and V-tools SVS-50 – skew chisels, parting tools and carving tools AX-40 – axes SVX-150 and SC-60 – scissors SVH-320 – planer blades DBS-22 – twist drills 3–22 mm The HTK-906 and TNT-808 kits collect the most common jigs for hand tools and woodturning respectively.

Question 28

What is the difference between Knew Concepts Mk.III, Mk.IV and Mk.V?

Accepted Answer

All Knew Concepts fret saws have a strong, light aluminium frame that keeps the blade under high tension. The models differ like this: Mk.III – the lightest model, with screw or lever tension Mk.IV – a triangulated truss frame that tensions the blade to 23–27 kg, much stronger and with less vibration. Red powder coat. Mk.V – the same strong frame as the Mk.IV, with longer blade clamps that have sight holes so you can see the blade is held Titanium – a welded titanium frame, the strongest and stiffest For the Mk.III, Mk.IV and titanium saws there is a foam handle grip that makes the handle thicker and easier on the hands.

Question 29

Which throat depth should I choose for a Knew Concepts fret saw, 3", 5" or 8"?

Accepted Answer

The throat depth is the distance between the blade and the back of the frame, and decides how far in from the edge of the work you can cut: 3" (76 mm) – stiffest and lightest, best for small and fine work such as jewellery and marquetry 5" (127 mm) – the most versatile choice for most work 8" (203 mm) – reaches furthest into larger panels, but the frame is longer and slightly less stiff If you are unsure, 5" is a good first choice. If you already have a saw, a 3" can be a good complement for detail work.

Question 30

Lever, cam lever or screw tension – which should I choose on a Knew Concepts fret saw?

Accepted Answer

It comes down to how often you change or release the blade: Lever / cam lever tension – flip the lever forward to release the tension, move the blade and flip it back. The tension is the same every time. Best when you cut many inside holes and often re-thread the blade. Screw tension – the tension is set with a screw. Simpler and less expensive, and works well if you rarely change blades. Swivelling blade clamps let you turn the blade a full turn with click stops every 45°, so you can make long cuts where the frame would otherwise hit the work.

Question 31

Which Tremont nail should I choose?

Accepted Answer

Tremont makes cut nails in the traditional way in many types. Some common choices: Common nail – framing, rough carpentry and face-nailing floors and panelling Flooring nail – hardened, for blind-nailing tongue-and-groove hardwood floors Rosehead nail – a button-shaped head, for furniture, cabinets, panelling, doors and wide floorboards Fine finish nail and brad – a small, discreet head, for mouldings and joinery Boat nail – hot-dip galvanized, for boat building Masonry nail – hardened, for fixing into mortar All Tremont nails are sold individually, so you can buy exactly the number you need.

Question 32

Should I choose hot-dip galvanized, black oxide or plain Tremont nails?

Accepted Answer

The finish decides where the Tremont nail fits: Hot-dip galvanized – rust-protected and recommended for all outdoor use Black oxide – a dark finish with an antique look, for exposed nailing indoors Plain – for indoor use, where it develops a natural patina over time Black oxide and plain nails can rust in damp conditions and stain tannin-rich woods such as oak, so choose galvanized outdoors.

Question 33

How do I drive cut nails without splitting the wood?

Accepted Answer

A cut nail is wedge-shaped with a blunt tip that cuts the fibres instead of wedging them apart. It holds well and is less likely to split the wood, if you orient it correctly: Place the wider face of the nail parallel to the grain , so the wedge shape does not push the fibres apart Pre-drill in hard wood and near ends and edges, with a hole slightly smaller than the nail's thickness Do not nail too close to end grain Rosehead nails are soft enough to be clenched, that is, bent over on the back, for extra holding power.

Question 34

How do I mix milk paint?

Accepted Answer

Both Real Milk Paint and Sweet Pickings come as a powder that you mix yourself with water, in the ratio 1 part powder to 1 part water: Pour the water into a jar and add the powder Stir or shake thoroughly until smooth Let it stand for a few minutes and stir again Thin with a little water if you want a wash or a thinner first coat Mix only as much as you will use, as mixed milk paint keeps for a limited time. If the paint foams, you can add Real Milk Paint anti-foam, which also makes pigments that tend to float on the water easier to mix.

Question 35

Does milk paint need a finish?

Accepted Answer

Milk paint dries to a matt, porous surface that can show water marks and wear. A finish protects the paint and deepens the colour: Pure tung oil or hemp seed oil – penetrates, deepens the colour and gives good water protection Wax – a soft sheen and a fine feel, but needs renewing Oil Wax (Sweet Pickings) – durable and water-repellent, one coat is enough Finishing Cream – a water-based protective finish that does not change the colour, gloss, satin or dead flat Oil and oil wax make the colour slightly warmer and can yellow slightly on white surfaces. If you want to keep a light colour exactly, Finishing Cream is a good choice.

Question 36

Can I apply milk paint over a painted or varnished surface?

Accepted Answer

Milk paint adheres best to bare, porous wood, where it soaks in and bonds very well. On painted, varnished or oiled surfaces the paint has more difficulty adhering and can flake. If you are painting a previously finished surface, sand off as much of the old finish as possible and make a test patch first. Some people use the flaking on purpose to get a worn, antique effect (chippy look). Milk paint can also be layered in several colours and sanded through for patina.

Question 37

How much milk paint do I need?

Accepted Answer

A 1 quart package of Real Milk Paint makes about 0.95 litres of ready milk paint, which covers about 3.3 m² with two coats. A pint (0.47 litres) covers about half that. Coverage depends on the surface: bare, porous wood absorbs more paint than a sanded, dense surface. Since you only mix the amount you need, you can keep the rest of the powder for the next project, so it is better to buy a little too much than too little.

Question 38

Which Kreg pocket-hole jig should I choose?

Accepted Answer

All Kreg pocket-hole jigs drill the same type of pocket hole. The difference is how fast and conveniently you work: R3 and 310 – small and portable, good for occasional projects and repairs 320 – two drill guides for faster work 520PRO – the most versatile, with VersaGrip clamping that rotates 360° 720 and 720 PLUS – a bench jig with Automaxx auto-adjust clamping for 13–38 mm material, for bigger projects XL – extra-large pocket holes in 2 × 4 and 4 × 4 timber The drill bit for Kreg pocket-hole jigs is 9.5 mm (3/8"). If you are unsure, the 720 is the most convenient choice for furniture and joinery.

Question 39

Which Kreg screw should I use for pocket holes?

Accepted Answer

Two things decide which Kreg screw you need for your pocket hole: Length – by the material thickness, for example a 25 mm screw in 13 mm material, 32 mm in 19 mm material and 64 mm in 38 mm material Thread – coarse thread for soft wood such as pine, plywood and MDF, fine thread for hardwoods such as oak and beech Kreg screws have a wide head that pulls the joint tight and a self-drilling tip that reduces the risk of splitting. The screw kits contain the most common lengths and threads and are a good start if you are new to pocket-hole joinery.

Question 40

How do I plug Kreg pocket holes?

Accepted Answer

Visible pocket holes can be hidden with plugs. You get the best result with plugs of the same wood as the project, so they blend in. With the Kreg custom pocket-hole plug kit you cut plugs in standard, Micro and Heavy-Duty sizes. Fit the drill guide block in your 700-series pocket-hole jig, such as the 720 or 720 PLUS, and drill with the plug cutter. Glue in the plug, let it dry and saw or plane off the excess flush with the surface.

Question 41

Can I buy spare parts for my tool?

Accepted Answer

We only keep some spare parts in stock, such as blades, rollers and a few parts for Veritas and Lie-Nielsen. Other spare parts we order from the manufacturer. Get in touch and tell us which tool and part it concerns, ideally with a photo. We then contact the manufacturer, such as Veritas, Lie-Nielsen, PEC or Incra. Since we order from some suppliers only a few times a year it can take time. For Veritas, Incra and Lie-Nielsen it is usually quickest to contact the manufacturer directly. Tormek parts can be added to our next order.

Question 42

Is a Lie-Nielsen plane complete when I buy it?

Accepted Answer

Yes. All Lie-Nielsen planes are supplied complete and ready to use, with frog, chip breaker and a lapped A2 blade. You do not need to buy the blade separately. Iron body means the plane body is cast iron, as opposed to the bronze models. PM-V11 is not available for Lie-Nielsen, as it is Veritas' own steel. The plane comes in a brown box with the Lie-Nielsen logo on the lid, which is easy to gift wrap.

Question 43

Which JessEm dowelling jig kit should I buy to get a complete jig?

Accepted Answer

JessEm makes two types of dowelling jig: The black one – first buy the dowelling jig with body and 8 mm kit, which includes the body and reference square. You can then add kits for 6, 10 and 12 mm. The stainless steel one – each size is complete on its own, so you can buy the size you need. The hobby kit has one base and several sizes, and the pro kit has all sizes complete with their own base. The 45° accessory for the stainless steel jig can be bought later. The stainless steel jig comes in an inch version (08359) and a metric version (08379). A guide pin is included with each size, but not a drill bit. To centre holes in 15 mm stock, put a 1 mm spacer against the fence.

Question 44

Can I run the Pégas scroll saw without the foot pedal?

Accepted Answer

Yes. Pégas scroll saws work without the foot pedal. You start and stop the saw and set the speed with the knob at the front of the arm. The foot pedal is an accessory that fits the SCP16CE, SCP21CE and SCP30CE. It lets you start and stop the saw with your foot and keep both hands on the work, which is handy when you often re-thread the blade for inside cuts.

Question 45

Does the Kreg Track Horse fit Swedish 45 mm studs?

Accepted Answer

The Kreg Track Horse is an American product, and the holders for the boards are made for American lumber that is 38 mm (1 1/2") thick. Swedish studs are usually 45 mm thick and therefore do not fit the holders without adapting them, for example by planing them down to 38 mm. The trestle itself and the bench clamp work as normal. Kreg makes no European version.

Question 46

Which saw blades fit the Knew Concepts fret saw?

Accepted Answer

Knew Concepts fret saws use standard plain-end blades, not pinned blades. All our wood and multi-purpose scroll saw and fret saw blades with plain ends fit, including in the deep 8" saws. Each blade type comes in several numbers. Low numbers are thin with fine teeth for thin stock and tight curves, and high numbers cut faster in thick wood. Thanks to the high blade tension, the saws also handle the finest blades. A Skip No. 7 blade comes with the saw, and the blade length is 130 mm (5").

Question 47

What do I need for the Veritas camber roller, and can the Mk.II roller be replaced?

Accepted Answer

The camber roller is an accessory for the Veritas Mk.II honing guide (05M09.01) and gives a slightly cambered edge on plane blades. It does not fit the narrow blade guide. The roller on the Mk.II guide can be replaced. The standard guide has a straight roller, and a spare roller is available separately. The deluxe set has both the straight roller and the camber roller. The camber roller can also be bought separately for a standard guide.

Question 48

Do 8 mm shank router bits fit the Trend T1?

Accepted Answer

Yes. The Trend T1 is a compact router that takes bits with shanks up to 8 mm. All Trend router bits and sets with 8 mm shanks therefore fit. Bits with 1/2" (12.7 mm) or 12 mm shanks do not fit the T1; they need a larger router. If you have bits with 6 mm or 1/4" shanks, you need a collet in that size.

Question 49

Which collets fit the JessEm Pow-R-Tek router motor?

Accepted Answer

The JessEm Pow-R-Tek SR router motor uses standard ER20 collets . It only comes with collets for 1/4 and 1/2 inch, so for bits with 6, 8 or 12 mm shanks you will need to buy additional collets. ER20 collets are available from well-stocked machinery and online shops. They are sometimes sold in a fixed size (for example 12 mm) and sometimes as a range (for example 12–13 mm) that covers every size in between. Note that only the collet itself can be swapped, not the nut, because the JessEm nut has a different thread from the one commonly used in Sweden. We do not sell ER20 collets ourselves.

Question 50

Which router fits the JessEm Mast-R-Lift II?

Accepted Answer

The JessEm Mast-R-Lift II is not tied to the JessEm motor. You can use any round router or router motor within the lift size range, which is a motor diameter of 81.7–106.7 mm, for example models from Bosch, DeWalt, Porter Cable and Makita. The JessEm Pow-R-Tek router motor is the largest that fits, and the Trend T1 is the smallest we have found that fits.

Question 51

Is the Incra Miter 1000SE metric?

Accepted Answer

Yes, the Incra Miter 1000SE we sell is the metric version. The scale and the stop are graduated in millimetres. The miter gauge has the Incra angle lock with 41 preset positions across 180°, and with the included telescoping fence and Flip Shop Stop you get accurate cuts, from 90° crosscuts and picture frames to advanced joinery.

Question 52

Can the Veritas Low-Angle Jack plane be used on a shooting board?

Accepted Answer

Yes, the Veritas Low-Angle Jack plane works very well on a shooting board. Veritas themselves recommend it if you do not want to buy their dedicated shooting plane. To set it up better for shooting, consider an extra blade for shooting board use, with a 38 or 50 degree bevel, which is better suited to planing end grain. That way you can keep the standard blade for general planing.

Question 53

What is included in the Veritas Dowel Maker Master set?

Accepted Answer

The Veritas Dowel Maker Master set already includes the insert set (Dowel Maker Insert Set), so you do not need to buy it separately. The Dowel Inserts for Arrow Makers are not included. The master set is discounted, so it is better value than buying the Basic Dowel Maker and the insert set separately.

Question 54

Do Veritas miniature planes come with a blade?

Accepted Answer

Yes. Veritas miniature tools always come with the blade fitted, and there is no other blade to choose. The product description tells you which steel the blade is made of. On the full-size Veritas planes, such as the Veritas right-hand shooting plane , you choose the blade yourself, unless the product page says otherwise.

Question 55

What is the difference between the Lie-Nielsen standard and tapered dovetail saw?

Accepted Answer

There is not a big difference between the two Lie-Nielsen dovetail saws. On the tapered dovetail saw the blade tapers slightly from toe to heel. This gives a little more control in precise cuts, since the blade is slightly above the line on the back of the work when you reach the line on the front. If you want a Lie-Nielsen dovetail saw, the standard one works just as well for most people. Both have a brass back, a Swedish steel blade and a cherry handle.

Question 56

Do Benchdogs accessories fit Festool and Makita guide rails?

Accepted Answer

Not always. The Benchdogs Rail Square is made differently for each brand of track saw and guide rail, and sometimes only the size of a screw differs. A Rail Square for DeWalt will therefore probably not fit a Festool or Makita rail. For a more detailed answer about the differences, ask Benchdogs directly. We stock the Benchdogs Quad Hinge system in a basic version, with separate bags of pins for the different machines. If you want Festool, for example, select Festool on the product page before adding it to your cart. If there is no option for your brand, those pins are temporarily out of stock.

Question 57

Which screws and bolts fit Veritas T-slot tracks?

Accepted Answer

It depends on which Veritas T-slot track you have: Narrow T-slot track (for example 610 mm, 12K79.22): made for 1/4-20 hardware, with T-slot nuts or T-bolts. Also available in 914 and 1219 mm. Wide T-slot track (for example 1200 mm, 12K79.38): made for 5/16-18 hardware. Standard M8 bolts also fit. Also available in 600 and 900 mm. With special hex bolt washers, sold as accessories, you can use ordinary hex bolts. Nuts, bolts and washers are sold separately.

Question 58

Which blades fit PEC combination squares?

Accepted Answer

Parts for PEC combination squares come in two sizes, and parts of the same size fit each other: Large version: parts of 300 mm or longer fit together, for example 300, 450 and 600 mm blades Small version: 100 mm and 150 mm parts fit together All blades are metric unless stated otherwise. The photos may sometimes show an imperial scale, but what we keep in stock is mainly the metric versions. We can order imperial versions for you, but expect it to take a while.

Question 59

How many Brusso L-39 hinges do I need per door?

Accepted Answer

For one door you need one pack of Brusso L-39. Each pack contains two hinges, a pair, which is what it takes to hang a door on offset pivot hinges. If you are hanging several doors, simply order one pack per door. If you have questions about fitting them or which hinge suits your project, feel free to get in touch with us.

Question 60

Which drill bit and reamer do I need for a Veritas tenon cutter?

Accepted Answer

It depends on which Veritas tenon cutter you have: Straight tenon cutter (05J41): the rounded shoulder at the base of the tenon is not meant to go into the hole, only the straight tenon. So all you need is a drill bit for the hole Tapered tenon cutter (05J46): cuts an angled tenon, and there is a matching reamer that bores the hole at the same angle For the straight tenon cutter an ordinary Forstner bit of the same size works well, for example a 3/4" bit for a 3/4" cutter. Regular wood drill bits of the same size work too.

Question 61

What does S in the item number of a Japanese saw mean – is the handle included?

Accepted Answer

If the item number of a Japanese saw ends in S , it is a replacement blade, meaning the blade only, without a handle. If you want a complete saw, choose the item without the S. If you ordered a replacement blade by mistake when you wanted a whole saw, it can be exchanged. Place a new order for the saw you want and mention in the comment that you have a return, and we will take care of the rest. Keep in mind that a new saw often costs about the same as a loose blade, since the handles are not expensive.

Question 62

What is the difference between Naniwa Professional and Naniwa S2?

Accepted Answer

Naniwa Professional (the P series) is a considerably better stone. Naniwa has not cut any corners there and has made the best stone they can. Naniwa S2 is by no means bad; it is enough for most people sharpening their tools. If you want a little extra and the price seems reasonable to you, the Professional series is a good choice. For a more detailed comparison, Naniwa has comparison charts on its website.

Question 63

Does the Pégas scroll saw come with a bench stand?

Accepted Answer

No, not as a separate part. The base is built into the saw itself, so the Pégas scroll saw sits steadily on the bench without an extra stand. An earlier product text saying the saw came with a sturdy bench stand was misleading, and the manufacturer has removed that point. If you would like the saw on its own stand, Pégas makes an adjustable stand as an accessory for each model: SCP16CE, SCP21CE and SCP30CE.

Question 64

What is the difference between York HV 582 and HV WM 582?

Accepted Answer

York HV 582 and HV WM 582 are both screws for a wagon vise. The difference is how you turn the screw: HV 582 has a wooden handle HV WM 582 has an iron handwheel instead Pick the version that suits your workbench and the way you prefer to work. If you have questions about fitting it, feel free to contact us.

How can we help you?

Search on blog

Products